Pins

A technician cleaned the flame sensor on a gas furnace in Lincolnton, North Carolina. The system components were inspected and confirmed to be in good condition. The furnace is now heating correctly.

Taylored Air installed a new heat pump and air handler in Lincolnton, NC, enhancing precise indoor temperature control and lowering energy costs. This upgrade supports efficient HVAC performance, ideal for local seasonal climate demands.

Taylored Air thoroughly cleaned all heating system hoses, drains, and filters, restoring optimal heat output. This HVAC maintenance was completed in Lincolnton, North Carolina, ensuring reliable winter comfort.

TAYLORED AIR inspected an HVAC unit in Gastonia, North Carolina. The team identified noise caused by an incorrect filter and advised using thinner filters. They re-insulated the refrigerant lines and flushed the drain line. The system now runs correctly after service.

Taylored Air inspected a Goodman straight AC with electric strip furnace. The technician confirmed the blower was clean and the system was heating properly. This HVAC service ensured the unit was functioning efficiently for safe and consistent indoor heating. Location data was not provided for this check-in.

Taylored Air inspected a Goodman Gas Pack in Lincolnton, North Carolina. The technician confirmed all components are operating properly. Burners and flame sensors were clean and did not require further service.

A technician in Gastonia, North Carolina repaired an ICP gas pack that was not heating. They replaced the ignition control board, reconnected the bypassed pressure switches, and corrected wiring issues. The heating system now operates correctly.

Taylored Air performed an HVAC system inspection in Lincolnton, NC, confirming the capacitor and contactor are functioning correctly with no repairs needed, ensuring reliable heating and cooling performance this season.

Taylored Air removed a blockage from a blower wheel caused by a mouse in a residential HVAC unit in Huntersville, North Carolina. The technician cleared the obstruction, reinstalled the blower wheel, and confirmed that the system operates correctly.

Taylored Air inspected a heat pump system in Lincolnton, North Carolina. Technicians confirmed proper freon levels and verified that both standard and emergency heat functions were operating correctly. The heat pump system was found to be working efficiently with no issues detected.

Taylored Air performed a thorough gas furnace maintenance in Lincolnton, NC, confirming proper operation and zero carbon monoxide levels, ensuring a safe and efficient heating system for homeowners this winter.

On November 20, 2025, a Taylored Air technician replaced a faulty capacitor on an outdoor HVAC unit in Lincolnton, NC, restoring reliable cooling performance and preventing future system failures.

Taylored Air inspected two HVAC units in a residential property in Hickory, North Carolina. Both systems operated correctly and displayed accurate readings. The technician confirmed that each unit was functioning within normal parameters.

Taylored Air replaced a faulty blower motor in a Lincolnton, NC home’s HVAC system on November 20, 2025. This repair restored optimal airflow, enhancing energy efficiency and indoor comfort during seasonal temperature changes.

Taylored Air installed a Ruud package heat pump in Lincolnton, North Carolina, optimizing residential heating and cooling efficiency. This unit enhances year-round climate comfort while reducing energy costs for homeowners.

A technician added Freon to recharge an HVAC system in Lincolnton, North Carolina, restoring proper refrigerant levels. This service improved indoor heating efficiency, ensuring the system heats reliably during colder months for homeowners.

A technician from Taylored Air inspected a heating system in Newton, North Carolina. The technician confirmed that the heat, emergency heat, and defrost cycle all function correctly. This service ensured proper winter operation and system reliability.

Taylored Air expertly relocated an outdoor HVAC unit to the back of a Lincolnton, NC home, enhancing airflow and system efficiency while freeing up valuable space near the original site for safer maintenance access.

TAYLORED AIR installed a Friedrich Breeze heat pump in Lincolnton, North Carolina, enhancing residential heating and cooling efficiency for year-round comfort.

A technician from TAYLORED AIR inspected a heater in Lincolnton, North Carolina. They confirmed the capacitor was functioning correctly and the heater strips were operating as expected. This check ensures heating systems work safely and efficiently during colder seasons.

Taylored Air completed HVAC maintenance in Hickory, North Carolina. The technician confirmed that the heat, emergency heat, and defrost cycle of the Goodman split system were operating correctly. The service also included cleaning the drain line to support proper system function.

Technicians replaced a damaged blower motor and broken mount that caused shaft instability. This HVAC service restored proper system operation in Cherryville, North Carolina.

TAYLORED AIR installed foam seals in Lincolnton, NC homes to boost insulation and air control, reducing energy loss and enhancing HVAC efficiency during seasonal temperature changes.

TAYLORED AIR completed a heat pump inspection in Lincolnton, North Carolina. The technician confirmed that the system is heating properly. Both the blower wheel and evaporator coil are clean and functioning efficiently.

Taylored Air performed preventative maintenance on a gas furnace in Lincolnton, North Carolina, cleaning the square trap and clearing a clogged drain line to maintain efficient operation and prevent future system issues.

TAYLORED AIR replaced a faulty TXV and filter dryer in Lincolnton, NC on Nov 19, 2025, restoring optimal airflow and cooling efficiency for reliable home comfort.

TAYLORED AIR inspected a thermostat in Lincolnton, North Carolina. The system reads the correct temperature and successfully activates the second stage of heating. The unit operates as expected and shows no performance issues.

Taylored Air installed a new inducer and collector box in a residential HVAC system in Conover, North Carolina. Post-installation carbon monoxide testing confirmed zero CO levels, ensuring safe and efficient operation for homeowners.

Taylored Air restored a heating system in Shelby, North Carolina by switching it from emergency heat to normal heat. The team also cleared a blockage in the drain line and confirmed all system levels were functioning correctly.

Taylored Air repaired a broken flare and fixed a cut lineset in Lincolnton, North Carolina. The service ensured the HVAC system maintained proper refrigerant flow and continued safe operation.

Taylored Air completed a heat pump system check in Lincolnton, North Carolina. The technician confirmed the drain is clear, the blower is clean, and the outdoor unit capacitor is operating within range. The system successfully cycled through defrost and is functioning properly overall.

A technician in Lincolnton, North Carolina adjusted fan speed settings on a 10kW heater kit that was causing power issues. The fan was changed from low and medium high to medium high and high. This resolved the tripping problem, and the system now operates correctly.

Taylored Air cleaned the inducer aperture and gas ports in Lincolnton, NC. The technician ensured the temperature differential met standards and confirmed no carbon monoxide presence for safe home heating.

Taylored Air inspected an air handler in Lincolnton, North Carolina. The system's heat and emergency heat functions were working correctly. The only issue found was dirt buildup on the coil.

TAYLORED AIR installed a new Ruud package heat pump in Lincolnton, NC, enhancing year-round energy efficiency and indoor comfort. This system reduces utility costs and ensures reliable climate control through seasonal temperature changes.

A technician from TAYLORED AIR inspected a heating system in Lincolnton, North Carolina. They confirmed that heat, emergency heat, and the defrost cycle were functioning correctly. The technician also removed a vine that had grown into the outdoor coil to prevent future obstruction.

Taylored Air inspected the heater kit in Gastonia, North Carolina, confirming all components function properly with no adjustments needed during this fall maintenance check.

A technician in Gastonia, North Carolina repaired damaged furnace wiring caused by flame rollout and a broken limit switch. The repair included rewiring, relocating the flame sensor and spark igniter. The heating system now functions correctly and maintains normal operation.

A technician in Cherryville, North Carolina repaired a short cycling heating unit by diagnosing a failed contactor. After replacing the damaged component, the system resumed normal heating operation.

Taylored Air inspected a heating system in Lincolnton, NC, confirming the defrost cycle and heat strips operate properly. The unit heats efficiently, ensuring reliable winter comfort and optimal energy use for homeowners.

In Lincolnton, North Carolina, a TAYLORED AIR technician replaced a broken low-voltage fuse inside a Ruud gas furnace on November 12, 2025. Following the replacement, the system's voltage was tested to confirm restored power and reliable heating, ensuring efficient warmth for local residents during colder months.

A technician in Conover, North Carolina inspected a furnace and found a rusted inducer motor housing with visible damage. The system displayed error codes. The technician recommended replacing the inducer motor assembly and the heat exchanger collector box due to corrosion.

A technician in Lincolnton, North Carolina cleaned the flame sensor and cleared the drain line on a gas furnace. The ignition system now operates properly, and no carbon monoxide or gas leaks were found. The furnace is producing consistent heat.

TAYLORED AIR replaced a faulty reversing valve and installed a new filter dryer on a heat pump in Lincolnton, NC. This November 2025 service restored efficient heating operation and improved system reliability for homeowners.

On November 12, 2025, TAYLORED AIR replaced a blocked HVAC drain line featuring a problematic 90-degree angle with a new P-trap in Lincolnton, NC. This repair restored proper drainage, preventing future clogs and ensuring efficient system operation for homeowners.

Taylored Air installed a PTAC heat pump system in Hickory, North Carolina. This system provides both heating and cooling, making it suitable for climate control in residential or small commercial spaces. PTAC units are often used in hotels, apartments, and offices for reliable indoor temperature management.

Taylored Air inspected a heat pump system in Lincolnton, North Carolina. The blower motor operated normally, and airflow remained consistent across all registers. Supply and return temperatures were within expected limits. The heating system performed efficiently and maintained the set indoor temperature without issues.

A technician from Taylored Air inspected a heating system in Lincolnton, North Carolina. The heat, emergency heat, and defrost cycle were tested and confirmed to be operating correctly. This service ensured the system functions reliably in cold weather conditions.

Taylored Air inspected a heating system in Lincolnton, North Carolina. Technicians tested the defrost cycle and confirmed correct entry, timing, and reversing valve function. They also checked the blower wheel to ensure it was clean, balanced, and free of debris.

Taylored Air inspected a gas furnace in Lincolnton, North Carolina. Technicians confirmed the capacitors were functioning and the flame sensors were clean. The furnace operated properly during the check.

Taylored Air performed HVAC maintenance in Lincolnton, NC, confirming a clean coil and thoroughly cleaning the blower wheel to optimize airflow and system efficiency during the November service.

A technician from Taylored Air completed a gas furnace inspection in Cherryville, North Carolina. The furnace is operating correctly and producing heat as expected.

Taylored Air inspected a mini split system heating efficiently in Statesville, North Carolina. Technicians verified the blower wheel, coil, and filters are clean, ensuring optimal performance this heating season.

Taylored Air cleaned an outdoor HVAC unit to remove algae and confirmed the electric heating strips were functioning properly in Hickory, North Carolina.

In Lincolnton, North Carolina, a technician replaced a faulty gas valve that received 24 volts but failed to open. This repair restored proper heating operation for the homeowner.

TAYLORED AIR serviced an HVAC unit in Lincolnton, North Carolina. The team confirmed the unit was operating correctly, cleaned the drain, and recommended installing an EZ trap for improved maintenance. The system was in excellent condition and functioning as expected.

Taylored Air completed installation of a new Goodman heat pump in Lincolnton, NC, enhancing year-round indoor comfort and reducing energy costs by upgrading outdated HVAC systems to modern, efficient technology.

Taylored Air inspected a heating system in Shelby, North Carolina. The 10kW heat strips operated correctly, the capacitor met specifications, amp readings were stable, and the refrigerant charge was within range. All components functioned as expected during the service.

During a November maintenance visit in Lincolnton, NC, Taylored Air sprayed off the outdoor HVAC unit and verified the system is running properly, ensuring reliable home comfort.

A technician in Lincolnton, North Carolina, restored an HVAC system after it froze. The technician removed a clogged air filter and installed a clean replacement to improve system airflow and function.

Taylored Air cleaned condenser coils and replaced a correctly sized capacitor during a November 2025 service in Lincolnton, NC, restoring the air conditioning system’s optimal performance ahead of summer heat.

Taylored Air inspected a condenser unit in Lincolnton, North Carolina. The technician confirmed the capacitor and components were functioning correctly. The unit’s heating performance matched the manufacturer’s chart specifications, indicating proper operation.

TAYLORED AIR installed a new Mitsubishi Mini Split system in Cherryville, North Carolina, enhancing year-round indoor comfort and significantly reducing energy costs for the homeowner.

Taylored Air inspected a heating system in Lincolnton, North Carolina. The technician confirmed proper operation of the heating, defrost, and emergency heat functions. All components were in good condition and functioning as expected.

TAYLORED AIR inspected a Rheem HVAC system in Lincolnton, North Carolina. The team verified proper heating performance, tested a 10kw heat kit, and confirmed the blower wheel and evaporator coil were clean. They also ensured the capacitor measured within range and refrigerant levels were correct.

TAYLORED AIR installed a UV light and surge protector on a Rheem heat pump in Lincolnton, NC, ensuring improved air quality and electrical protection. Post-installation tests confirm optimal system operation.

Taylored Air serviced a RUUD heat pump in Lincolnton, NC, cleaning the drain, verifying the defrost cycle, and checking freon levels. The system operates efficiently, ensuring reliable heating during North Carolina's colder months.

Taylored Air repaired wiring for a zone damper and reconnected thermostat #2, restoring efficient zoned HVAC control and comfort in Lincolnton, North Carolina.

A technician in Lincolnton, North Carolina corrected a furnace issue by draining water from the exhaust and adjusting the pipe. The exhaust was not level, which caused water to collect and the furnace to shut off. The pipe was repositioned to direct water back toward the furnace outlet.

TAYLORED AIR cleared a clogged drain line and confirmed emergency heat operation in Lincolnton, North Carolina. The technician inspected both HVAC systems, noting a clean blower wheel and overall good condition, ensuring reliable performance.

Taylored Air inspected a RUUD Gas Pack in Shelby, North Carolina. The coil and blower motor were clean, and all components operated correctly. This check confirmed the system’s proper function and cleanliness.

Taylored Air added drain cleaner to the pan and checked the system in Lincolnton, North Carolina. The technician confirmed the coil remains in good condition, and the temperature differential is within optimal range. The air conditioning system is running properly without any performance issues.

Taylored Air installed a new Bosch heat pump in Lincolnton, North Carolina, enhancing heating and cooling efficiency while reducing energy costs year-round through advanced HVAC technology and expert system calibration.

TAYLORED AIR cleaned the coil using coil cleaner on a mini split system in Newton, North Carolina. The technician confirmed the outdoor unit and indoor unit are both operating correctly and providing proper heating.

A TAYLORED AIR technician replaced a burnt service disconnect in Morganton, NC, restoring safe electrical function. The HVAC system passed post-repair testing and operates reliably.

Taylored Air inspected a main package HVAC unit and two mini split systems in Newton, North Carolina. The team confirmed the heat strips, defrost cycle, and all units were functioning correctly. This service ensured proper heating system operation before seasonal use.

A technician from TAYLORED AIR replaced a faulty inducer motor in a Lincolnton, NC gas furnace on November 7, 2025. This repair restored proper ignition and heating function, ensuring reliable winter warmth.

TAYLORED AIR inspected an HVAC system in Lincolnton, North Carolina, confirming proper defrost function and freon levels within the optimal range. This maintenance ensures efficient heating performance during colder months for local homeowners.

A technician in Lincolnton, North Carolina replaced a noisy HVAC contractor component. The heating system now functions correctly and operates without unusual sounds.

Taylored Air installed a Fujitsu Mini Split system in Hickory, NC, enhancing year-round comfort with precise room temperature control. The energy-efficient setup reduces utility costs and is ideal for seasonal climate variations in the region.

Taylored Air replaced a failed HVAC contractor in Lincolnton, North Carolina. The new installation resolved the issue, and the system now runs properly. This service ensured safe and consistent heating and cooling performance for the property.

A technician from Taylored Air cleaned the HVAC drain line in Hickory, North Carolina. The system now heats and cools as expected. This service helps prevent blockages and supports proper system function.

Taylored Air replaced a blown fuse caused by a faulty contractor, restoring reliable heating in a Lincolnton, NC home during the cold season. The system now operates safely and efficiently, ensuring homeowner comfort.

A technician in Lincolnton, North Carolina cleaned the blower wheel and coil on a RUUD heat pump. The system was inspected and confirmed to be operating normally after the cleaning service.

A technician from Taylored Air assisted a homeowner in Lincolnton, North Carolina, with starting their heating system. The system was activated successfully and is operating as expected.

Taylored Air installed a new Friedrich heat pump in Lincolnton, North Carolina, ensuring efficient heating and cooling for the home. The system enhances temperature control and energy efficiency, reducing utility costs during seasonal weather changes.

Taylored Air completed a detailed HVAC system inspection in Lincolnton, North Carolina, confirming optimal operation with no repairs needed during the November 2025 visit.

Taylored Air inspected the outdoor HVAC unit in Lincolnton, North Carolina, confirming electric heat strips are in good condition and the system operates efficiently.

A Taylored Air technician replaced a blower control board in Huntersville, NC, restoring the HVAC system's functionality and improving airflow for efficient heating and cooling.

A technician in Mooresville, North Carolina diagnosed a Carrier gas pack that was overheating and shutting down after five minutes. After consulting with support, they improved airflow by adding return air. The system now heats correctly without triggering the limit switch error.

Taylored Air inspected a Mitsubishi mini split system in Lincolnton, NC, confirming it operates properly with no faults detected during this November 2025 preventative maintenance visit.

Taylored Air serviced a Carrier mini split unit in Lincolnton, North Carolina. Technicians confirmed the unit operated correctly, with clean blower wheels and evaporator coils. They also cleaned the filter during the visit.

TAYLORED AIR inspected a recently installed Friedrich mini split unit in Lincolnton, North Carolina. The technician confirmed the system is operating correctly and does not require further adjustments at this time.

In Lincolnton, NC, a technician from TAYLORED AIR replaced a faulty TXV and filter dryer on November 3, 2025, restoring heating efficiency and reliable system performance for winter comfort.

Taylored Air inspected a RUUD heat pump in Lincolnton, North Carolina, confirming balanced indoor split temperatures and proper component operation, ensuring efficient heating and cooling performance for the homeowner.

Taylored Air replaced a faulty electric heat kit contractor in Lincolnton, North Carolina, after diagnosing a blank thermostat caused by a blown fuse. The heating system and auxiliary heat now operate correctly. This service restored full heating function and ensured reliable temperature control.

A technician cleared a water-filled pressure switch hose and checked the furnace drain system in Lincolnton, North Carolina. Water was added to the collection box to confirm proper flow to the condensate pump. The furnace is now functioning correctly.

A technician from TAYLORED AIR inspected a gas furnace and heat pump in Lincolnton, North Carolina. The system is operating correctly. The technician confirmed that the flame sensor and drains are clean and functioning as expected.

Taylored Air repaired a grounding issue that was shutting down the flame sensor in an HVAC system in Gastonia, North Carolina. The technician connected the ground correctly, which stopped the system from reversing polarity and restored proper function.

Taylored Air inspected an HVAC system in Newton, North Carolina. Technicians confirmed the capacitor and refrigerant levels are within range. They verified the blower wheel and evaporator coil are clean. The system is heating as expected and shows no signs of malfunction.

Taylored Air inspected a heating system in Lincolnton, NC, confirming proper heat output and system efficiency during the October maintenance visit.

Taylored Air completed a heater kit and capacitor installation in Lincolnton, North Carolina. The new components functioned properly after setup, restoring performance to the heating system. This service ensured reliable operation ahead of colder weather.

A technician from Taylored Air replaced a faulty blower motor in a Lincolnton, NC HVAC system, restoring heating and cooling performance to normal operation promptly.

A technician from Taylored Air replaced a faulty gas valve and checked for gas leaks in Lincolnton, North Carolina. No leaks were found after the installation, confirming the system's safety and proper operation.

On October 29, 2025, Taylored Air performed essential HVAC maintenance in Lincolnton, NC, vacuuming the drain line and verifying the heating and defrost cycles operated efficiently. All components were inspected and found fully functional.

Taylored Air replaced a faulty sequencer on a downstairs heating unit in Lincolnton, North Carolina. The issue caused only one side of the RUUD 10kW heater kit to activate. A new sequencer was installed, restoring full functionality to the system.

A Taylored Air technician cleared a clogged heat exchanger in an HVAC unit in Lincolnton, NC, restoring proper airflow and efficient heating performance. Regular maintenance like this prevents costly repairs and ensures reliable indoor comfort during colder months.

TAYLORED AIR inspected two Goodman heat pumps in Shelby, North Carolina. Technicians cleaned and flushed the drain lines, confirmed both heater kits functioned properly, and verified the defrost cycles during the visit. All systems operated correctly after the service.

Taylored Air flushed the HVAC drain line and verified system operation during maintenance in Lincolnton, NC. Regular servicing prevents clogs, ensuring efficient and reliable home comfort year-round.

A technician in Lincolnton, NC reconnected a disconnected water sensor on a furnace, restoring normal operation so the system heats efficiently and reliably.

Taylored Air installed a Mitsubishi Mini Split system in Lincolnton, North Carolina. The system provides efficient heating and cooling for improved indoor comfort. This installation supports precise temperature control and operates quietly, making it suitable for residential or small commercial spaces in the area.

TAYLORED AIR inspected a Lennox heat pump in Huntersville, North Carolina. The system operated correctly, and the customer enrolled in the Pro Comfort Plan.

Taylored Air activated emergency heat for the AC system and completed comprehensive heating and cooling maintenance in Lincolnton, NC, ensuring all systems operate efficiently and reliably.

Taylored Air replaced a breaker, tested heat strips for proper output, and cleaned the drain line on an HVAC system in Lincolnton, North Carolina. These actions restored reliable heating and prevented drainage issues during seasonal use.

A technician in Lincolnton, North Carolina replaced a burnt disconnect in a crawlspace, restoring stable heating function to the home’s heat pump system during the October heating season.

Taylored Air inspected a heating system in Gastonia, North Carolina. The team verified the thermostat settings, confirmed proper ignition function, and cleaned the drain line, flame sensor, and igniter. Carbon monoxide levels were checked with no detection reported.

TAYLORED AIR installed a homeowner-provided Ecobee thermostat with a sensor in Lincolnton, North Carolina. The upgrade was needed after a computer was moved near the original thermostat. The new system improves temperature control and ensures more consistent cooling and heating throughout the home.

Taylored Air relocated a mini split system for a customer in Cherryville, North Carolina. The team ensured proper installation in the new spot to maintain system performance and indoor comfort.

TAYLORED AIR performed preventative maintenance in Lincolnton, NC by cleaning the HVAC drain line and pan, confirming ignition protocols functioned correctly, ensuring efficient system operation and preventing costly repairs.

Taylored Air installed a new American Standard gas pack unit in Lincolnton, NC, providing energy-efficient heating and cooling with enhanced temperature control and system reliability for local homeowners.

TAYLORED AIR cleared a partially clogged drain line in Lincolnton, NC, ensuring the heat cycle, heat strips, and defrost functions operated correctly post-service for optimal winter performance.

Taylored Air reconnected a detached OB wire to restore heating in a Lincolnton, NC home, ensuring the system operated correctly during the cold season.

Taylored Air installed an ionizer and confirmed proper system performance in Gastonia, North Carolina. The technician also checked and cleaned the flame sensor to ensure efficient operation.

Taylored Air performed a full HVAC system check in Hickory, North Carolina. The technician confirmed the blower and coil were clean, tested the heater kit for proper operation, and verified that the outdoor unit functioned correctly during the inspection.

Taylored Air inspected an HVAC unit in Lincolnton, North Carolina. The technician checked system performance, confirmed proper refrigerant levels, tested the capacitor, and found no leaks. The team vacuumed and flushed the drain line to support consistent system function.

Taylored Air inspected a heating system in Morganton, North Carolina. The technician tested the auxiliary heat, replaced a stretched blower belt, and confirmed proper function with correct amp draws on all motors.

TAYLORED AIR replaced a faulty capacitor in a Fort Mill, SC HVAC system on October 24, 2025, restoring full operation and improving energy efficiency for the homeowner during peak seasonal use.

TAYLORED AIR inspected a heating system in Cherryville, North Carolina. The team confirmed proper system function, verified that coils and the blower wheel were clean, and cleared a clogged drain line to maintain efficient operation.

TAYLORED AIR cleaned the drain and rinsed the HVAC coil in Lincolnton, NC, removing dust buildup. This maintenance improved airflow, enhanced system efficiency, and helps prevent seasonal HVAC issues for homeowners.

Taylored Air inspected the defrost system in Lincolnton, NC on October 21, 2025, confirming optimal operation with no repairs needed, ensuring efficient winter performance.

TAYLORED AIR replaced furnace burners and cleaned igniters and flame sensors in Lincolnton, NC, ensuring efficient heating performance this fall.

Taylored Air inspected a gas furnace and confirmed proper operation. Technicians verified the gas tank is full, burners are functioning normally, and the flame sensor is clean. This routine check ensures the system is ready for consistent heating performance. Location data was not specified.

TAYLORED AIR installed a Fujitsu mini split system in Gastonia, North Carolina. The team set up the unit to provide efficient heating and cooling while maintaining consistent indoor temperatures. This type of system offers a compact solution for regulating room-specific climate without ductwork.

A technician in Hickory, North Carolina, replaced a faulty defrost board on a heating system. They tested the auxiliary heat and defrost cycles. Capacitors measured within normal range, and refrigerant levels were confirmed as adequate. The system is now operating correctly.

In Lincolnton, NC, a TAYLORED AIR technician ensured furnace efficiency by cleaning the flame sensor, checking the capacitor, confirming a blue flame, and verifying inducer amperage, helping homeowners maintain safe, reliable heating during colder months.

Taylored Air inspected a heating system in Lincolnton, North Carolina. The technician confirmed the system is heating correctly, tested auxiliary heat and defrost mode, verified refrigerant levels, and checked that the capacitor remains within its proper range.

Taylored Air completed an HVAC system inspection in Lincolnton, NC, confirming proper function with clean coils, correct refrigerant levels, and a clean blower wheel for efficient performance.

Taylored Air inspected a furnace and condenser in Lincolnton, NC, confirming all components operated correctly. The ignition sequence passed, ensuring efficient, clean combustion for reliable heating performance.

Taylored Air inspected an HVAC system in Cherryville, North Carolina. The technician checked refrigerant pressures for both heating and cooling modes, confirmed proper system function, and verified that the capacitor operated within the correct range.

Taylored Air inspected an HVAC system in Lincolnton, NC on October 16, 2025. They tested the defrost cycle and auxiliary heat function, verified refrigerant levels, and checked capacitor values, confirming the system operates efficiently for homeowner comfort.

Taylored Air inspected an HVAC system in Lincolnton, North Carolina. Technicians confirmed that the heating, cooling, and defrost cycles are functioning correctly. The visit ensured the system operates within expected parameters for performance and efficiency.

Taylored Air inspected an HVAC system in Lincolnton, North Carolina. The technician confirmed the drain was clear and the condensate pump was operating correctly. This check ensured proper system function and efficient moisture removal.

Taylored Air completed a new HVAC unit installation in Lincolnton, North Carolina. The system was inspected and confirmed ready for winter conditions. This service ensures consistent indoor heating and reliable performance for the colder season.

A technician in Lincolnton, North Carolina replaced a leaking Schrader valve and missing gasket cap. They cleaned the HVAC coils and filters, then increased the fan speed. These actions improved suction pressure and confirmed proper temperature splits, helping restore efficient system performance.

Taylored Air completed a system inspection in Lincolnton, North Carolina. Technicians verified that all components were operating correctly. This service ensured the HVAC system functioned without issues and required no repairs at the time of check-in.

TAYLORED AIR completed a thorough HVAC system inspection in Lincolnton, NC, confirming the equipment operates efficiently with no issues detected during the October 2025 visit.

Taylored Air re-wired a faulty thermostat in Lincolnton, North Carolina, restoring accurate temperature control and reliable heating during cooler months. Post-repair testing confirmed the system maintained consistent warmth throughout the home.

Taylored Air cleared a blocked drain and removed standing water from an air handler in Lincolnton, NC. Post-service tests confirmed proper drainage and system function, preventing water damage and ensuring reliable HVAC performance this season.

TAYLORED AIR installed a new Fujitsu mini split system in Lincolnton, North Carolina. The team completed the HVAC installation to support efficient climate control in the space. This service improves indoor temperature management with a compact and effective solution.

Taylored Air replaced a noisy double pole contact and corroded 5KW heat kit contactor in Lincolnton, NC, restoring heating efficiency and eliminating electrical noise to prevent future system faults and reduce energy waste.